Showing results: 1 - 15 of 531 items found.
-
-
Finero OY
The electrical safety test is carried out for each commonly connected Appliance. The conduction testing of high voltage, insulation resistance, grounding is most commonly performed.
-
SCR ELEKTRONIKS
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
LS9955/56 -
Lisun Electronics Inc.
The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.
-
9901HTX-72x24x12 -
Hydraulic Technology, Inc.
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
9901HTX-36x36x15 -
Hydraulic Technology, Inc.
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
19200 -
Chroma ATE Inc.
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
IBEKO Power AB
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
EN62471-C -
Lisun Electronics Inc.
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Chroma ATE Inc.
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
SCR ELEKTRONIKS
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
Parker Hannifin Corp.
Parker Chomerics offers a wide variety of EMI/EMC and safety testing for regulatory compliance. Tests include FCC, EC, VCCI, IEC 1000 (formally 801) EN 61000 Series, CISPR, Austel, MIL-STD-461 and EU regulations
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),